FAAC XT2 868SLH Remote Control Frequency 868 MHz - 2 Channels

Sync-ed with original fob, instructions easy to do this. Works perfectly!

Amazing and highly recommendedBut check your existing remote frequency and type first before buying. In my case we had an old FAAC remote where I found the 868-MHZ frequency-reference on the print board inside.The packed in instructions are limited and confusing.However - please read the VERY clear instructions of one of the top reviewers (Rattycube, February 2016) & don't forget to be polite and give him/her your "helpful" vote!.The set up took me less then 3 minutes. And it works.So very good value for money given that our gate company was going to charge me 60 GBP for a new remote control.We'll see how durable the device is, but it didn't miss my low expectations. And I will update the review if necessary.I'm not using the flimsy supplied cord and small metal ring to connect it to my key chain, as I fear it will simply break soon through wear.

It works well. Needs to be paired so needs a working fob to pair to, which might be an issue if you are replacing a broken one.

We purchased this as a direct replacement to the FAAC DL2 868SLH which has been discontinued. Because I had looked at the instructions several times it took me a couple of minuets to program a new "master" remote/transmitter.My advice before even contemplating doing any of this this look at the videos and instructions before even pressing a button. It will save you allot of headaches. it is relatively straight forward when you watch the videos!If you’re looking for a good set of instructions go directly to the FAAC UK website. Select Product Range --> Accessories --> Radio Control, --> Coding Instructions 868Mhz.There are two ways to code this device. Coding using and existing "master" remote OR Coding to a Receiver.1. Coding using and existing "master" remote, essentially cloning.If you are trying to code/clone it using an existing remote, it is essential that the existing remote is a master and not a slave remote. If it is a slave you have to set-up the device using the receiver, option 2. I spoke to the tech department at FAAC and the chap said that to create a Master remote you have to choose the 2nd Option and Code the device directly to the receiver.How to recognise a master/slave transmitter- Master: If you press any key of a master transmitter, the LED flashes before becoming steady- Slave: If you press any key of a slave transmitter, the LED goes on immediately with steady lightDifferences between master and slave transmitter- Master: Only a master transmitter can transfer its “system code” to decoding card/RP receivers and to other Transmitters (master or slave).-Slave: Unable to transfer its “system code and, therefore cannot be either duplicated, or used for coding systems. Can learn the “system code” from a master transmitterCoding instructions - Coding using an existing "master" remoteTransmitter Coding1. Take a WORKING transmitter and push buttons P1 and P2 simultaneously. The LED will start to flash.2. Let go of both buttons, the LED should remain flashing for 10 seconds and then press and hold the button that works the gates already, the LED should now be steadily lit.3. Keeping the button held down, pick up the new transmitter and touch the two together LED to LED.4. STILL keeping the working transmitter button held down, also press and hold the same button down on the NEW transmitter as well5. Now you’re holding down the same button on each transmitter, the LED on the NEW transmitter should flash twice and go out6. Let go of the button on the NEW transmitter.7. Now let go of the button on the WORKING transmitter.8. Point the NEW transmitter at the gates and press and hold down the button you have just coded for approximately 2 seconds, nothing will happen.9. Let go and then press and hold it again. Your transmitter should log on to the decoder (which is what the transmitters talk to, in order to operate the gate/door) and start to work10. Repeat steps 1 to 9 for any other new transmitters you have2. Coding to a Receiver (my preferred option).If you are going to code the remote at the receiver it is imperative you take allot of care and know exactly which button(s) to press before starting. If you don't have a "master' transmitter (remote) you will have to use this option.Coding instructionsTransmitter (remote) Coding using a RP receiver1. Take a WORKING transmitter (remote) and push buttons P1 and P2 simultaneously. The LED will start to flash2. Let go of both buttons, and press and hold P1. there should be a steady blue light.3. Whilst holding P1 on the transmitter (remote) press and keep holding the button on the RP receiver, a red LED will turn on and off, on and off and then on4. let go of the button on the RP receiver5. Let go of P1 on the transmitter (remote)6. Press P1 on the transmitter for 2 seconds and you should notice the red LED appears on the RP Receiver, then let go7. Repeat step six by pressing P1 on the transmitter for 2 seconds and the red LED appears giving the command for the operator to move.8. Process completeNB. there are different types of receivers such as an RP, E124, E024s. The latter two require different buttons being pressed. please go to the FAAC website at the top of the review for a specific guide.

I had to return this item as it failed to program from my master fob,

Great! Synced perfectly

Replaced a FAAC DL4 with this one (the soft touch grey remote with red light). My gate is two swing gates and the buttons open one gate and two gates together (pedestrian and car). Check back of existing remote for signal (433 or 868) - and then buy the right one.For programming - press two buttons on old remote together until light flashes continuously* (and remains flashing) then press the button you want to programme on old remote and the button you want to programme on new remote. That's it, it is a bit fiddly/hit-and-miss, but just go into a quiet place and work it out...it will seem easy when you have done it!* I just tried the two buttons I use the most, and you might need to try different combinations, just make sure the light is flashing when you try and programme it.

this is extremely good value. The reason for purchasing is that one of the buttons on the original unit I have had for around 10 years in daily use finally lost its "spring return". The batteries had never been replaced. I looked around Amazon for replacement and this one was certainly best value. I fully support the comments on the more modern multi-language instruction sheet; they look very difficult to follow. I attach a photo of the instructions I used to program my replacement unit (came with the original). Please note that these instructions relate to programming a new unit with an existing one (I borrowed from a family member).Hope this helps.