Deliver to UAE

For best experience Get the App

Teyleten Robot DC 1 Channel Optocoupler 3V/3.3V Relay High Level Driver Module Isolated Drive Control Board 3V/3.3V Relay Module for Arduino (Pack of 5)

Teyleten Robot DC 1 Channel Optocoupler 3V/3.3V Relay High Level Driver Module Isolated Drive Control Board 3V/3.3V Relay Module for Arduino (Pack of 5)

Q: I'm still not clear with the jumpers are for. What does optoisolation do here?

There are a few reasons why you would use isolation here. By the way, jumpers are for isolation - although the top jumper is futile. To use the optoisolator, disconnect the bottom jumper and connect the left pin to ground for the signal coming in to the board and connect the right pin to the ground of the voltage that activates the relay. The VCC should be connected to the voltage source that operates the relay (or if you want to remove the top jumper, vcc goes to the right pin, however it is the same as leaving the jumper on and just wiring it to the vcc input on the board. - I have used this setup to run a bank of relays off of an esp32. This allows you to run many relays without any significant voltage drop on the esp32. You will need to provide an alternate vcc for the relays. Imagine running 15 relays off of the ESP32. That would possibly cause a voltage issue on the board. If all you need to do is run 15 tiny leds (I guess 30 if you include the indicator on the board) your voltage drop would be much much lower. Because this uses optoisolation, the circuit that sends the signal (usually a microcontroller) and the voltage that powers the relay, can be totally isolated. You could use a battery for one and a computer usb for the other - no common ground between the two. -- Not pointless by any means, but the circuit setup for this is goofy and causes you to scratch your head for a minute.

Q: I put 3.3v on vcc and grounded gnd. when i put 3.3v on in, the red led lights, but the relay doesn't close. is there something i'm missing here?

It should work. You are controlling a Transistor that is operating the relay. Make sure there is enough current in VCC to activate the relay. LED will light with only 1.3v and very little current. The relay must have 3.3V VCC. Also make sure your Arduino output line has the same ground as board. Using separate power supplies can cause the problem. Otherwise, I need more details about your connection.

4.4/5

Product ID: 184934785

Secure Transaction

12 interest-free installments with tabby

Details

Connector Type
Crimp
Contact Material
Silver
Contact Type
Normally Open
Current Rating
10 Amps
Mounting Type
Panel Mount

⚡10A Load

🔌3V/3.3V Power

🛡️Optocoupler Isolation

Frequently Bought Together

Teyleten Robot DC 1 Channel Optocoupler 3V/3.3V Relay High Level Driver Module Isolated Drive Control Board 3V/3.3V Relay Module for Arduino (Pack of 5)

AEDIKO 4pcs DC 5V Relay Module 1 Channel Relay Switch Relay Board with Optocoupler Isolation Support High or Low Level Trigger

ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Ribbon Cables Kit Compatible with Arduino Projects

Description

🔧 Elevate Your Projects with Precision Control!

PACK OF 5 - Get more for less—perfect for scaling your projects without breaking the bank.
VERSATILE VOLTAGE - Designed for 3V and 3.3V systems, making it ideal for Arduino projects.
SEAMLESS ISOLATION - Optocoupler technology ensures safe and reliable control, protecting your circuits.
USER FRIENDLY DESIGN - Easy to integrate into your existing setups, even for beginners.
POWERFUL COMPATIBILITY - Handles up to 10A at 250VAC and 30VDC, perfect for diverse applications.

The Teyleten RobotDC 1 Channel Optocoupler Relay Module is a high-level driver board designed for 3V/3.3V systems, featuring a robust 10A load capacity and photocoupler isolation for enhanced safety and reliability. This pack of 5 modules is perfect for Arduino enthusiasts looking to expand their project capabilities.

Have a Question? See What Others Asked

I'm still not clear with the jumpers are for. What does optoisolation do here?

Will 3v power the relay?

I want to run this realy on a 2 AA battery box (3v total) do i need to do anything with jumpers?

I put 3.3v on vcc and grounded gnd. when i put 3.3v on in, the red led lights, but the relay doesn't close. is there something i'm missing here?

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Suresh K.

Very impressed with the quality and fast delivery. Will shop here again.

4 days ago

Meera L.

Smooth transaction and product arrived in perfect condition.

3 weeks ago

View all Trustpilot reviews

Shop Global, Save with Desertcart

Value for Money

Competitive prices on a vast range of products

Shop Globally

Serving over 300 million shoppers across more than 200 countries

Enhanced Protection

Trusted payment options loved by worldwide shoppers

Customer Assurance

Trusted payment options loved by worldwide shoppers.

Desertcart App

Shop on the go, anytime, anywhere.

AED 59

Duties & taxes incl.

UAEstore

Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction

12 interest-free installments with tabby

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Vikram D.

The MOLLE sheath is of exceptional quality. Very happy with my purchase.

2 weeks ago

Khalid Z.

Great experience from order to delivery. Highly recommended!

1 week ago

View all Trustpilot reviews

DOWNLOAD THE APP

WE SOURCE ITEMS FROM

UAE
UK
INDIA
USA
JAPAN

Customer Services

About Us

Customer Support