Teyleten Robot DC 5V-36V 15A Max 30A 400W Dual High-Power MOSFET Trigger Switch Drive Module 0-20KHz PWM Adjustment Electronic Switch Control Board DC Motor Speed Controller for Arduino 10pcs
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6

Teyleten Robot DC 5V-36V 15A Max 30A 400W Dual High-Power MOSFET Trigger Switch Drive Module 0-20KHz PWM Adjustment Electronic Switch Control Board DC Motor Speed Controller for Arduino 10pcs

4.0/5
Product ID: 223089846
Secure Transaction
12 interest-free installments with tabby
15A Power
🔄0-20KHz PWM
🔋400W Capacity

Description

⚙️ Power Up Your Projects with Precision!

  • ARDUINO READY - Seamlessly integrate with your Arduino projects.
  • UNLEASH THE POWER - Harness up to 15A and 400W for your projects!
  • PWM PRECISION CONTROL - Adjust speed effortlessly with 0-20KHz PWM.
  • DUAL MOSFET EFFICIENCY - Experience lower resistance and higher performance.
  • VERSATILE VOLTAGE RANGE - Supports 5V-36V for maximum compatibility.

The Teyleten RobotDC Dual High-Power MOSFET Trigger Switch Drive Module is a robust electronic switch control board designed for DC motor speed control. With a wide voltage range of 5V-36V and a maximum output of 15A and 400W, it is perfect for high-power applications. The module features dual MOSFETs for enhanced efficiency and supports PWM adjustments from 0-20KHz, making it an ideal choice for Arduino enthusiasts and professionals alike.

Have a Question? See What Others Asked

Which mosfet is on the board? can't buy without knowing!

Reviews

4.0

All from verified purchases

L**M

Good, Low Side Switch

Note that this is a "Low Side" switch. This means the switch controls the -Vin side. Thus if you are trying to use this in an application where the load is "grounded", it will not work. You must use this with loads that have their low side (- VDC) isolated. Other than that, it works well. It will trigger reliably at a trigger voltage as low as 3.2 VDC although the "on" resistance is a bit higher at lower trigger voltages. If you allow the trigger to linger between 0 VDC and about 3.0 VDC, you will rapidly destroy the switch. It needs a fast rise and fall time trigger signal. With a 3.3 VDC trigger, Vin of 12 VDC and a load of 60 W (5 A at 12 VDC), I measured a loss of 0.4 W in the switch.

J**N

Small but work well for powering 24v fans from Orange Pi 3 GPIO

These boards are pretty small, and I would prefer to have mounting holes on all four corners of the board plus bigger wire terminals. But they do seem to be working well for powering my three 24v 5015 fans (in parallel) from my Orange Pi 3 GPIO. For the price, I'd definitely recommend them. Keep in mind that these are meant for low current. Don't try to power a bed heater through them. I'd probably say 100 watts or less. I don't think I'd trust the 400w rating at all simply due to the small size of the board and its tiny circuit paths.

T**R

NIce and easy units to use.

Purchased these units for a couple of upcoming projects. All passed bench test with flying colors. Found the effective operational frequency response was around 60 khz. Much higher than the rated 20 khz. All units met or surpassed ratings. Next test will be some long-term power testing. Will buy again if needed.

A**S

Burns out easily

As one other person mentioned, this is a low side switch (Vin+ and Vout+ are connected while Vin- and Vout- are the 2 that are controlled by the PWM signal). Also similarly to another review, the rated current on this switch is a scam. Connecting to a DC motor powered by a 3s lipo they burn one after another. I wouldn't recommend if you are actually going to run a motor off of these. (Honestly wouldnt even recommend for a 2s lipo)

R**R

Work very well for gpio fan control

I used a pair of these for PWM control of 24V fans in a 3D printer using the Raspberry Pi GPIO ports. They work well for this. Note that MOSFET control is on the low (negative) side of the fan or light connection.

M**M

Excellent Mosfets at an unbelievable price!

Worked as expected! I love how compact they are, they fit nicely in my electronics enclosures for all of my 3D Printers. I'm using them to control LED light bars with PWM via Marlin's Case Light menu, absolutely no issues!

N**O

If only...

I was excited to find a cheap - large pack of simple speed controllers that can handle 15A rather than me ripping out the pot on other controllers. Whelp - my excitement was misplaced. Burned the first one I tested at 2.5A of current after only about 2 mins - the thing smelled hot after 15 seconds. Not to mention, the terminals are tiny - couldnt possibly accept any wire that would carry 10A safely anyways. Do yourself a favor - unless you want to run these at 1/10th of their "rating" - dont buy them.

S**S

Pequeño pero potente

Recibi lo que pedí y me siento muy conforme, gracias

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Suresh K.

Very impressed with the quality and fast delivery. Will shop here again.

4 days ago

Reema J.

Perfect platform for hard-to-find items. Delivery was prompt.

1 month ago

Shop Global, Save with Desertcart
Value for Money
Competitive prices on a vast range of products
Shop Globally
Serving millions of shoppers across more than 100 countries
Enhanced Protection
Trusted payment options loved by worldwide shoppers
Customer Assurance
Trusted payment options loved by worldwide shoppers.
Desertcart App
Shop on the go, anytime, anywhere.
AED 53

Duties & taxes incl.

UAEstore
1
Free Shipping

with PRO Membership

Delivery Partners: iMile, Transcorp

Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction
12 interest-free installments with tabby

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Abdullah B.

Great price for an authentic product. Fast international shipping too!

3 weeks ago

Suresh K.

Very impressed with the quality and fast delivery. Will shop here again.

4 days ago

Teyleten Robot Dc 5v 36v 15a Max 30a 400w Dual | Desertcart UAE